Handheld metal detector coil on dry grassland, portable underground metal searching prospecting equipment product banner

100 + 400 MHz Dual-Frequency Ground Penetrating Radar丨GEO-GPR-S

PRODUCT PARAMETERS

GEO-GPR-S 100 + 400 MHz dual-frequency ground penetrating radar combines 100 MHz deep-penetration band and 400 MHz high-resolution band, delivering co-located dual datasets in one survey pass — depth-oriented solution for karst, bedrock and infrastructure subsurface investigation.
  • 100 + 400 MHz Dual-Band Integration, Balanced Deep Penetration & Shallow Detail Resolution
  • Single-Pass Co-Located Acquisition, Eliminating Cross-Dataset Registration Deviation
  • Up to 30 m Max Detection Depth (100 MHz Band) in Dry Low-Loss Ground
  • 350 Traces/s High-Speed Scanning, >160 dB SNR for Reliable Signal Quality
  • Integrated Host-Antenna Design, Wireless Link & ≥8 h Continuous Field Operation
  • Three Switchable Acquisition Modes, Flexible for Depth / Detail-Focused Surveys
Description
FAQ
Get A Quote

Description

The GEO-GPR-S 100 + 400 MHz dual-frequency ground penetrating radar combines a 100 MHz low band for deeper structural investigation with a 400 MHz high band for clearer near-surface and target detail. Both bands are recorded at the same trace positions in a single survey pass, helping users interpret deep geological context and shallow features without merging two separately acquired datasets.

Designed for surveys where investigation depth is the primary requirement but near-surface detail is still important, the 100 + 400 MHz configuration is suited to deep karst, goaf and bedrock investigations, as well as corridor and infrastructure work that needs both depth context and layer resolution.

  • Two frequency bands, one survey pass: the 100 MHz band reaches structures that the 400 MHz band may not resolve at depth, while the 400 MHz band provides more detailed shallow imaging.
  • Co-located datasets: both bands are acquired at the same trace positions, reducing the registration gap and interpretation uncertainty that can arise when two separate survey runs are combined.
  • Depth-oriented configuration: the stated maximum detection depth is 30 m, governed by the 100 MHz low band. This reach applies to dry, low-loss ground; conductive or saturated ground can reduce penetration materially.
  • Integrated system: the high-band element is embedded in the low-band housing. The 100 + 400 MHz combination adds approximately 0.50 kg against the equivalent single-frequency GEO-GPR antenna.
  • Flexible acquisition: select low-band only, high-band only or dual-frequency acquisition to balance survey power, speed and data volume.
Ground Penetrating Radar Applications areas
ApplicationHow the Dual-Frequency Configuration Helps
Deep karst, cavity and goaf investigationUse the 100 MHz response to establish deeper subsurface context and the 400 MHz response to examine shallower boundaries and target detail.
Bedrock and overburden investigationAssess deeper structural conditions while retaining a higher-frequency dataset for near-surface layering.
Municipal roads and utility corridorsRelate shallow services and disturbed ground to deeper subsurface conditions on the same chainage.
Tunnel and infrastructure investigationCombine near-surface detail with deeper ground context where the survey objective extends beyond shallow inspection.

The antenna has a swath width of 0.82 m. Where survey specifications require 400 MHz line density, municipal survey codes may call for line spacing no greater than 0.5 m; the 100 + 400 MHz configuration therefore requires additional lines to meet that density. The antenna should be walked at the line spacing required by the tighter frequency band. If void acceptance work requires compliant 400 MHz line density, plan the line layout accordingly. If the governing requirement is a depth target beyond 5 m, the 100 + 400 MHz configuration is the depth-oriented choice in this product range.

ParameterSpecification
Centre frequencies100 + 400 MHz
Maximum detection depth30 m (100 MHz low band)
Swath width0.82 m
Total system mass28.45 kg
Envelope dimensions820 × 620 × 290 mm
Acquisition modesLow band only / high band only / dual-frequency, switchable
Scan rate350 traces/s
A/D conversion18 bit
Signal-to-noise ratioBetter than 160 dB
Total power consumption≤16 W
Continuous operating time≥8 h
Wireless data range≥50 m
Operating voltage10–15 V DC
Operating temperature−30 °C to +70 °C
Control and setupOne-click parameter setup with automatic acquisition configuration
DisplayReal-time display of both bands during the survey
System designIntegrated host-and-antenna design; compact, wireless and low power
Custom frequency combinationsAvailable on request

Depth note: Maximum depth is governed by the lower-frequency band and is quoted for dry, low-loss ground. Conductive and saturated conditions can reduce achievable depth materially.

Datasheet note: Time window, trace interval, survey speed, positioning option and ingress protection are published in the full technical datasheet and are available on request.

FAQ

① In SI, it is m·s-2, and one percent of it is the international unit abbreviation g.u.;
② Conversion between SI and CGS: 1g.u.=10-1 mGal

Gravitational field: The space around the earth with gravity is called the gravitational field.
Gravitational potential: The gravitational potential W in the gravitational field is equal to the work done by a particle of unit mass moving from infinity to that point.

① The normal gravity field of the earth: Assuming that the earth is a rotating ellipsoid (reference plane), the surface is glossy, the internal density is uniform, or it is distributed in concentric layers, the density of each layer is uniform, and the deviation of the shape of the ellipsoid from the geoid is very small, then the gravity field generated by the earth is the normal gravity field.
② The normal gravity value is only related to the latitude, the smallest at the equator and the largest at the poles, with a difference of about 50,000 g.u.; the rate of change of the normal gravity value with latitude is the largest at 45° latitude, and zero at the equator and the poles; the normal gravity value decreases with increasing altitude, and its rate of change is -3.086 g.u.. The main feature of the long-term change is the "westward drift" of the geomagnetic elements, both the dipole field and the non-dipole field drift westward, and have a global nature.

The gravitational field strength is equal to the gravitational acceleration in both numerical and dimensional terms, and the two are in the same direction. In gravity exploration, all references to gravity refer to gravitational acceleration. The gravitational field strength at a point in space is equal to the gravitational acceleration at that point.

Gravity exploration is an exploration method that is based on the density difference of rocks and ores. Since density difference will cause local changes in the normal gravity field of the earth (i.e. gravity anomaly), it is used to solve geological problems by observing and studying gravity anomalies.

REQUEST A QUOTE

REQUEST A QUOTE